Cooper Security Homelink 75 User Manual Page 1

Homelink 75 Security SystemUser Guide

Change DonePartition1. Partition 01 U2. Partition 02 U3. Partition 03 U4. Partition 04 UChange DonePartition1. Partition 01 U2. Partition 02 U

Select Stop12:15Setting OptionsSetting Partition 027 to Set01:1201/01/2005MenuUSUUWhen programming your system, the installer can mark

Omit All ViewSetting Faults6 FaultsStop12:15Setting with 6 zone(s) omitted7 to Set2a EITHER If any detectors are not yet ready to be set (othe

3 EITHER Press STOP. The display returns to the standby screen. OR Press OMIT ALL to omit the zones. The system sets with the faulty zones o

Select Stop12:15Setting OptionsSetting Partition 017 to SetDo this: The display shows:12 Press the appropriate button on the telecommand.

Press the same button again.Press the appropriate button on the telecommand.You may hear a warning tone from the control unit if a zone is not

Continued on next page.Change DonePartition1. Partition 01 U2. Partition 02 S>UThe control unit starts the entry tone.Do th

 If you see a icon in the top left hand side of the display when you unset, then there is a voice memo waiting. The display w

15:51ExitEnter Access CodeDo this: The display shows:12The system unsets all those partitions that you have access to.The control unit starts

Change DonePartition1. Partition 01 U2. Partition 02 S>UContinued on next page.U = unset. S = set. P = part set. S>U = will change from

Controls and Displays ...3Key Functions: ...4Access to the System .

Change DonePartition1. Partition 01 U2. Partition 02 S>UChange DonePartition1. Partition 01 U2. Partition 02 S01:1201/01/2005MenuUSUUDo thi

Note: If you want to unset a partition, press the appropriate button on your telecommand.21Do this: The display shows:

The table below shows the different kinds of alarms the control unit can raise.Signal (see note) Type of Alarm Started by:Lo

Reset All ExitReset RequiredP2:Burg Z02 AlarmThe siren stops and the screen shows the first zone to cause the alarm, for example:2EITHER The di

OR The installer may have programmed your system so that the screen will tell you where the alarm occurred, and also show a message asking you

When someone presses the Social Alarm button on the keypad, presses a button on a Social Care transmitter or starts an Inactivity

Homelink can call your phone to report an alarm. After listening to the message you can give the system commands by pres

To: Press:Listen in 1Talk 2Toggle listen/talk *Re-play messages 3End call 5Unset the system #0*0Set the system #0*1Part set the sytem

To make changes to the way your system works you must enter the User Menu. Your degree of access to the User Menu depends on w

Select ExitMenuVoice MemoThe following pages give short instructions on how to use each option of the User Menu. For more detailed instruction



1. Enter User Menu.2. Select Omit Zones.3. Press  or  to select zone to omit.4. Press Change so that end of line shows “O”.5.

1. Enter User Menu.2. Select Facilities On/Off.3. Press  or  to select item.4. Press CHANGE to switch On or Off.5. Press

1. Enter User Menu.2. Select Outputs On/Off.3. Press  or  to select output.4. Press change to switch the output o

1 to 0,*,# To operate the system you must identify yourself:Sets the whole system.Unsets the system.Scroll up

The display shows messages and prompts to help guide you through setting, unsetting and programming the system.W

Select SetSetting OptionsFull Set AllPart Set AllPartitionsOR Do this: The display shows:1 EITHER Ma

Notes: If you decide you want to stop setting then press STOP. If your system is full set, then you cannot go directly to part set. You must uns

Select Stop12:15Setting OptionsSetting All7 to SetWhile the system is set the display shows the standby screen.2The display shows how much time

Continued on next page.Select SetSetting OptionsFull Set AllPart Set AllPartitionsSelect SetSetting OptionsFull Set AllPart Set AllPartitions2OR