Cooper Security M2000 User's Guide Page 61
- Page / 180
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Engineering Manual Engineer Menu 1-4
53
The control unit operates the General Fault System Output at the same time as the RF
Jammed System Output.
151 – Tx Low Battery
The control unit operates this output when any MRNode reports a wirefree detector with
low battery. (There is a separate output type for Telecommands and PAs.) The output
remains on until all MRNodes stop reporting detectors with low batteries.
The control unit operates the General Fault System Output at the same time as the TX Low
Battery System Output.
152 – Telecommand Low Battery
The control unit operates this output when any MRNode reports a telecommand or PA
with low battery. The output remains on until all MRNodes stop reporting telecommands
or PAs with low batteries.
The control unit operates the General Fault System Output at the same time as the
Telecommand Low Battery System Output.
153 – Set Pulse
The control unit switches this output on for 10 seconds when a user sets any ward.
154 – Unset Pulse
The control unit switches this output on for 10 seconds when a user unsets any ward.
Ward Event Output Types
The following events are applicable if you have chosen the output to follow a specific ward:
00 – Bell-SAB
Activates when the selected ward is in alarm and the control panel bell output is on, and
deactivates when the bell output is off. The bell output may be activated on a confirmed
or unconfirmed alarm, depending on whether Bells on Confirm or Bells on Unconf is
selected (page 90).
01 – Strobe
Activates when the selected ward is in alarm and the control panel strobe output is on;
deactivates when the selected ward is reset.
02 – Switch 12
Activates when the selected ward is set; deactivates when the selected ward is in alarm, its
Entry Delay timer (page 61) is running or the ward is unset. This output is normally used as
an input to latching detectors.
03 – Det. Reset
Deactivates for approximately 4 seconds when a user code is entered to set the first ward.
The output is used to reset latching detectors (smoke detectors, shock sensors, etc.).
04 – Walk Test
Activates when the selected ward is walk tested (User option 1-1-2); deactivates when the
walk test is exited.
- Contents 3
- Contents Engineering Manual 4
- Engineering Manual Contents 5
- Preface 8
- Chapter 1: Introduction 9
- Network Wiring = 4 Core 11
- Engineer’skeypad 11
- (cannot have zones 11
- Control Panel Features 13
- Compatible Devices 14
- IDNode and MIDNode 15
- System Wiring 17
- 100m max 18
- Calculating Voltage Drop 19
- Table 1. Voltage Drop 20
- Voltage Drop Example 1 20
- Example 1 21
- Example 2 21
- Installation Instructions 22
- I=360mA I=180mA I=180mA 23
- Chapter 2: Getting Started 24
- Press [Ent] To 25
- Leave Menus 25
- About the Engineer Menus 26
- Options in Engineer Menu 1 27
- Step 1 – Select Zone 29
- Step 2 – Select Zone Type 29
- User's Guide 44
- Custom Output 49
- Keypad Installation 64
- Instructions 64
- Overview 75
- Option 1-5-3 : Exceptions 76
- Option 1-5-4: Auto Sets 78
- Example: Auto Setting 82
- Option 1-7: Customising Text 86
- Confirmation On 97
- Manager's Manual 104
- Introduction 105
- Sh o w s c u rr e n t 113
- [ENT] to CONFIRM 137
- 002 LEC2S 137
- Equipment 3 137
- Confirm Devices 137
- Equipment 7 139
- Default User 1 139
- [ENT] to DEFAULT 139
- Table 6. Default Settings 141
- Equipment 9 143
- Test Display 143
- 8888888888888888 143
- Manager's 147
- Log Event Codes 148
- 2:04:1 MSNode 154
- Not Learned 154
- 1:01:1 Not Used 154
- 5. TROUBLESHOOTING 156
- Appendix A: Text Keys 159
- Start Guide 160
- To program the system 161
- Commercial with Foyer Mode 162
- To Program the system 163
- Digital Communicator 164
- To Program the Communicator 165
- Test Call 165
- Dynamic Test Call 165
- Static Test call 166
- DD243: 2004 Compliance 167
- ACPO PA Reduction Policy 168
- Engineer Quick Reference 169
- Location Of : 172
- 1,Panel 2,Keypad 172
- Index Engineering Manual 174
- Engineering Manual Index 175
- Part No: 12039336 Issue 4 180
Related products and manuals for Security access control systems Cooper Security M2000
(56 pages)Samsung CTN464KC01 Handbücher
Bedienungsanleitungen und Benutzerhandbücher für Nein Samsung CTN464KC01.
Wir stellen 2 PDF-Handbücher Samsung CTN464KC01 zum kostenlosen herunterladen nach Dokumenttypen zur Verfügung Bedienungsanleitung
Comments to this Manuals